MyComfortHaven is reader-supported. As an Amazon Associate I earn from qualifying purchases.

Crafting Comfort: A Step-By-Step Guide To A DIY Zero Gravity Chair [2023 Updated]

Zero gravity chairs have revolutionized relaxation, providing unparalleled comfort by simulating a state of weightlessness. However, acquiring a manufactured zero gravity chair may not always be within budget, or perhaps you enjoy the satisfaction of a hands-on project.

Whatever your motivation may be, constructing your own zero gravity chair can be a rewarding challenge. This article will guide you through the process of creating your very own DIY zero gravity chair.

What You’ll Need

Here is a list of materials and tools you will need for this project:

  • Two pieces of solid wood (2×1 inch and 6 feet long) for the sides
  • Three pieces of solid wood (2×1 inch and 2 feet long) for the crossbars
  • Screws and washers
  • Strong, flexible fabric (such as canvas)
  • Four large, heavy-duty hinges
  • Power drill
  • Saw
  • Measuring tape
  • Staple gun
  • Bungee cords

Step-By-Step Guide

Follow the steps below to construct your own zero gravity chair:

1. Creating The Frame

The first step is to create the wooden frame of the chair.

diy zero gravity chair
  • Arrange the two 6-feet long wooden pieces parallel to each other. These will serve as the sides of the chair frame.
  • Measure and mark the positions for the crossbars on each side piece: one at the top (for the head), one about 2 feet from the top (for the seat), and one about 3.5 feet from the top (for the legs).
  • Attach the crossbars to the side pieces using screws and washers, making sure to line them up at your marked positions.

A. Cut The Wood

Cut the wooden pieces into two sizes. The 6-feet pieces will serve as the sides of the chair frame, while the 4-feet pieces will be the crossbars and the center support.

B. Assemble The Frame

Arrange the 6-feet pieces parallel to each other. Attach the 4-feet crossbars to the side pieces using screws and washers, one at the top (for the head), one about 2 feet from the top (for the back), and one about 3.5 feet from the top (for the legs).

C. Add The Center Support

The center support piece (2×1 inch and 4 feet long) should be attached between the crossbars for the back and legs, aligning with the middle of the frame.

2. Hinging The Frame

The next step is to create the reclining mechanism using hinges:

A. Divide Your Frame Into Two Parts

  • The upper part (backrest) and the lower part (seat and leg rest). The division should be at the seat crossbar.
  • Attach two hinges to the outer sides of the chair where the backrest and seat meet. Ensure that the hinges are correctly aligned, and the chair can recline smoothly.

3. Attaching The Fabric

Now you’ll need to attach your fabric to create the chair’s seat and backrest.

  • Cut your fabric into two pieces: one for the backrest and one for the seat and leg rest. Each piece should be large enough to wrap around the respective parts of the frame.
  • Begin by stapling the fabric for the backrest onto the frame, making sure it’s taut but has enough give to accommodate a person’s weight.
  • Repeat this step for the lower part of the chair.

4. Installing The Bungee Cords

The final step is to install the bungee cords. These provide the flexibility needed for the chair to recline and return to its upright position.

  • Drill holes in the side pieces of the frame, at intervals of around 5 inches.
  • Thread the bungee cord through these holes, starting from the top of the chair, going down one side, up the other side, and securing at the top again. The bungee cord should be tight, providing enough tension to support weight and bounce back.

Why Some One Need DIY Zero Gravity Chair?

Choosing to create a DIY Zero Gravity Chair could stem from various motivations. Here are some reasons why someone might decide to undertake this project:

1. Customization

Creating a DIY Zero Gravity Chair allows individuals to customize the chair to their specific preferences. They can choose the materials, colors, and dimensions that best fit their needs and home décor.

2. Cost Savings

High-quality zero gravity chairs can be quite expensive. By building one from scratch, individuals can potentially save money, especially if they already have some of the necessary tools and materials.

3. Personal Satisfaction

For DIY enthusiasts, the process of creating something with their own hands offers a sense of accomplishment and satisfaction. Building a zero gravity chair can be a challenging yet rewarding project.

4. Unique Features

When building their own zero gravity chair, individuals have the freedom to add unique features not typically found in commercial models. This could be anything from extra padding for comfort, specialized fabric, additional pockets for storage, or customized reclining settings.

5. Repair And Maintenance Skills

If someone has built their own zero gravity chair, they’re likely to have a better understanding of how to repair and maintain it. This can further save costs and extend the lifespan of the chair.

6. Sustainability

Building a DIY chair may also be a more sustainable option for those who are conscious about reducing waste. They can source reclaimed or recycled materials to use in their project.

Building a DIY Zero Gravity Chair is a blend of practicality, creativity, and personal satisfaction. While it’s a project that requires some investment of time and effort, the end result can offer a unique piece of furniture that perfectly fits the creator’s needs.


Crafting your own DIY zero gravity chair can be a fulfilling project that combines creativity, practical skills, and the satisfaction of creating your comfort space. By following these instructions and ensuring safety measures, you can enjoy the fruits of your labor in the form of a comfortable, relaxing, and personalized zero gravity chair. Remember that you can always add your personal touches, like adding cushions and other stuff.

Leave a Comment